The following chart indicates the fender products available to cover particular energy ranges. It also points out the features and benefits of various fender types.
Energy Range 50 Tonne-m & Large
Fender Type Arch Type Fender / V Type Fender
Features : A high efficiency fender which features rubber encapsulated steel mounting plates in its base; Rubber covered, slotted bolt holes are included; Available in a range of standard sizes and lengths.
Benefits : High energy absorption capacity is obtained while minimizing the reaction load; No exposed metal and a secure mounting ensure low maintenance and a durable installation; Easily installed and the range of available lengths will fit most designs.
Restrictions : There are length restrictions.
Energy Range 20-50 Tonne-m
Fender Type 1 Arch Type Fender / V Type Fender (see above)
Fender Type 2 Cylinder Type Fender
Features : Good performance characteristics are achieved; Fender can roll for even wear; It is available in a wide selection of sizes.
Benefits : Allows a wide range of ship sizes to use the pier; It is durable and easily accessible for maintenance or replacement.
Restrictions : Require large stand off distances; Exposed mounting hard-ware.
Fender Type 3 Large Profile Fenders (Block Type Fenders)
Features : Easily adaptable to specific mounting requirements.
Benefits : These low initial cost fenders are weel suited for parallel berthing in well protected conditions.
Restrictions : Mounting hard-ware is exposed.
Energy Range 10-20 Tonne-m
Fender Type 1 Arch Type Fender / V Type Fender (see above)
Fender Type 2 Large Profile Fenders (Block Type Fenders) (see above)
Fender Type 3 Bucking Columns
Features : Rubber encapsulated steel support plates. Good performance characteristics are achieved.
Benefits : Excellent durability with no exposed metals. Mounted behind a protective fender pile system.
Restrictions : Cannot be used for direct contact.
Fender Type Profile Fenders / D Type Fenders
Features : A large selection of shapes and sizes.
Benefits : Economical protection against wharf face damage.
Restrictions : Mounting hard-ware is exposed.
Arch Fender
JIER manufactures two types Arch Fenders, JDA-A and JDA-B. The JDA-A fender has a rubber contact face ideal for all general purpose applications...
Cylindrical Fender
Cylindrical Fenders are simple to install and operate which makes these units an economical solution for remote locations and for multi user berths...
Cone Fender
All Cone Fenders are single piece mouldings so they are robust, long lasting and easy to install. UHMW-PE faced steel frontal frames are generally used...
Super Cell Fender
Cell Rubber Fender here mentioned is improved over the ordinary type. It has high absorption energy per unit weight and low tilt compression performance...
D Fender
D Fenders can be pre-curved, chamfered and drilled to aid installation at a relatively low cost and can also be cut to the length required ...
Wing Fender
JIER Wing Type Rubber Fenders are developed on the basis of D Type Rubber Fenders. They can be fixed with double line anchors which greatly ...
Square Fender
Square Rubber Fenders offer similar advantages to D fenders and are typically used where a stiffer fender is required. Square Rubber Fenders...
Unit Element Fender
Unit Element Fenders are a high performance, modular system. Element Fenders can be combined in unlimited permutations of length, orientation and Energy...
Roller Wheel Fender
Roller and Wheel Fenders are commonly used on the berth corners and dock entrances, also widely installed along the walls of dry docks and other...
Tug Fender
Tug fenders must work harder, for longer and under more adverse conditions than any other fender type. Tug fenders can be divided into three main types...
Pneumatic Rubber Fender
Pneumatic Rubber Fenders have been in use for around 50 years. The development of the Pneumatic Fender has progressed through ...
Foam Filled Fender
Foam Filled Fenders are versatile, robust and suitable for almost all applications. The manufacturing process allows for virtually any size of fender to be...
Keyhole Fender
Keyhole Fenders are made of high abrasion resistance rubber. They are specially designed for tugboats and workboats.
Rubber Ladders
Rubber Ladders Fenders are very robust. They are flexible to reduce accidental damage and help protect the wharf from small craft berthing.
Rubber Pads
Rubber Pads (Plates) are designed and produced for the protection of barges, tugboats, water locks and quay walls.Contact Us
Feel free to contact us if you have any comments or inquires and one of our skilled staff representatives will contact you within the next business day.