Our Products
Marine Fender Systems
A modern marine fender system consists of many different components and materials. Rubber fenders are the heart of a marine fender system. All of JIER Rubber Fenders are designed and manufactured strictly in accordance with international standards and specifications. Furthermore, they are also approved by Bureau Veritas to the stringent PIANC 2002 and ASTM F-2192-05 guidelines.
Arch Fender
JIER manufactures two types Arch Fenders, JDA-A and JDA-B. The JDA-A fender has a rubber contact face ideal for all general purpose applications...
Cylindrical Fender
Cylindrical Fenders are simple to install and operate which makes these units an economical solution for remote locations and for multi user berths...
Cone Fender
All Cone Fenders are single piece mouldings so they are robust, long lasting and easy to install. UHMW-PE faced steel frontal frames are generally used...
Super Cell Fender
Cell Rubber Fender here mentioned is improved over the ordinary type. It has high absorption energy per unit weight and low tilt compression performance...
D Fender
D Fenders can be pre-curved, chamfered and drilled to aid installation at a relatively low cost and can also be cut to the length required ...
Wing Fender
JIER Wing Type Rubber Fenders are developed on the basis of D Type Rubber Fenders. They can be fixed with double line anchors which greatly ...
Square Fender
Square Rubber Fenders offer similar advantages to D fenders and are typically used where a stiffer fender is required. Square Rubber Fenders...
Unit Element Fender
Unit Element Fenders are a high performance, modular system. Element Fenders can be combined in unlimited permutations of length, orientation and Energy...
Roller Wheel Fender
Roller and Wheel Fenders are commonly used on the berth corners and dock entrances, also widely installed along the walls of dry docks and other...
Tug Fender
Tug fenders must work harder, for longer and under more adverse conditions than any other fender type. Tug fenders can be divided into three main types...
Pneumatic Rubber Fender
Pneumatic Rubber Fenders have been in use for around 50 years. The development of the Pneumatic Fender has progressed through ...
Foam Filled Fender
Foam Filled Fenders are versatile, robust and suitable for almost all applications. The manufacturing process allows for virtually any size of fender to be...
Keyhole Fender
Keyhole Fenders are made of high abrasion resistance rubber. They are specially designed for tugboats and workboats.
Rubber Ladders
Rubber Ladders Fenders are very robust. They are flexible to reduce accidental damage and help protect the wharf from small craft berthing.
Rubber Pads
Rubber Pads (Plates) are designed and produced for the protection of barges, tugboats, water locks and quay walls.Chains and Fittings
Chains and Fittings are used for two reasons – to suspend/support the rubber fender or to control the deflection geometry during horizontal or vertical shear. Chains and Fittings are an important component of a marine fender system and require careful design.
Mooring Bollards
In the maritime contexts in which the term originates, a bollard is either a wooden or iron post found as a deck-fitting on a ship or boat, and used to...
Mooring Ropes
Natural fibre ropes used to be the choice of impoverished sailors, but so little is made that it is now more expensive. It is hard, therefore, to justify...
Chains
Chains are used for two reasons – to suspend/support the fender or to control the deflection geometry during horizontal ...
Shackles
Shackles and other accessories are all referenced to the nominal chain diameter for equivalent strength and typically of larger diameter material.
U Anchors
U Anchor is an main accessory in marine rubber fender system. It is used to hold chains.
Bolts and Nuts
Bolts, Nuts and Washers are a set of fasten fittings. They are used as joint part between fender body and dock, steel panels and fender body, UHMW-PE facing pads and steel panels. Usually these fasten fittings are made of stainless steel, Q235 Hot galvanized.
Steel Panels
Steel Panels of Rubber Fenders are complex steel fabrications. They are connections of the rubber fender and the UHMW PE facing pad.
UHMW PE Facing Pad
UHMW-PE, Ultra High Molecular Weight Polyethylene, has become the material of choice for facing steel fender panels...
Marine Airbags for Ship Launching/Ship Pulling/Salvage
Ship launching using marine airbags is a very popular vessel launching method. It overcomes the shortcomings of the fixed launching track.
Marine Airbag Construction
Ship Launching/Pulling Airbags, basic body are consisted of our rubber layers, synthetic-cord-reinforced rubber layers, are kind of a cylindrical airbags ...
Marine Airbag Specification
The standard specification of marine airbags. You can choose the required diameter and effective length to meet your projects.
Marine Airbag Application
Marine Airbag Application Shipbuilding Industry: Upgrading and launching of ships; shipwreck salvaging; ships collision avoidance.
Marine Airbag Repair and Maintenance
Marine airbags can be used repeatedly; the correct using method and reasonable storage could extend the using life of them.
Single Pulley Block
A block and tackle system which combined with many pulleys is often in conjunction with a winch, mast or other lifting equipments...
Double Wheels Pulley Block / Double Sheave Block
JIER double wheel pulley block is in high quality. Capacity from 1ton to 32 tons. The diameter of sheave...
Three Wheels Pulley Block / Treble Sheave Block
Professional china Three - Wheel Pulley Block Manufacturer, Three - Wheel Pulley Block Supplier ...
Four Wheels Pulley Block / Four Sheave Block
JIER four wheels pulley block for lifting goods-On this Product Details Page, You Can Find Comprehensive.
Five Wheels Pulley Block / Five Sheave Block
Five-wheel Pulley Block Recommended Directory. You can Source Hot Five-wheel Pulley Block, crane wheel.
Six Wheels Pulley Block / Six Sheave Block
Professional china Six-Wheel Pulley Block Manufacturer, Six-Wheel Pulley Block Supplier，More types...